A 3.0 m ladder of mass 12 kg rests against a frictionless wall. The coefficient of friction between the ladder and the floor is 0.60. What is the smallest angle that the ladder can make with the ground if the ladder is to remain at rest? (in degrees) Neglect the friction between the ladder and the wall.
20
35
40
45
Unlock full course notes by signing up
Is the force exerted by the tendon attached to the forearm to hold the forearm horizontal greater than, equal to, or less than the weight of the forearm?
One end of a uniform 4.0 m-long rod of weight w{\small w}w is supported by a cable at an triangle of θ = 37°{\small \theta\ =\ 37\degree}θ = 37°with the rod. The other end rests against a wall, where it is held by friction, as shown. The coefficient of static friction between the wall end the rod is μs = 0.50.{\small \mu_s\ =\ 0.50.}μs = 0.50. Determine the minimum distance x{\small x}x from point A at which an additional weight w{\small w}w (the same as the weight of the rod) can be hung without causing the rod to slip at point A. Enter your answer in meters to the appropriate number of sig figs.
Calculate the net torque (magnitude and direction) on the beam through the point labelled O (i.e. an axis perpendicular to the page at point O) and (b) through an axis through C perpendicular to the page. Give your answers in Nm.
Find the net torque on the wheel below about the axle through Operpendicular to the page, taking a = 10.0 cm and b = 25.0 cm. (Note for clarification: the 12.0 N force is acting directly above the axis O, at an angle from that point.) Give your answer in units of Nm to the appropriate number of significant figures.
Forces: Torque
A seesaw of length 5m is supported at the center. A child of mass 35kg is sitting on one end. A second child of mass 45kg comes to play. Where should the second child sit in order to balance the seesaw? Enter your answer in meters, measured from the pivot axis of the seesaw.
A 3.0 m ladder of mass 12 kg rests against a frictionless wall. The coefficient of friction between the ladder and the floor is 0.60. Assume there is no friction between the wall and the ladder. What is the smallest angle that the ladder can make with the ground if the ladder is to remain at rest? (Enter your answer in degrees)
A 10 kg mass is hanging from a rope wrapped around a pulley. The falling mass causes the pulley to rotate. The mass of the pulley is 2 kg. What is the acceleration of the falling mass, and what is the tension of the rope?
A thin uniform rod (length=1m, mass = 5kg) is pivoted about a horizontal, frictionless pin through one end of the rod. The rod is released when it makes an angle of 60°60\degree60° above the horizontal. What is the angular acceleration of the rod at the instant it is released? (pick the closest answer)
A mass-less string is wrapped several times around a Cylinder . If the free end of the string is held in place and the Cylinder is released form rest, the string unwinds and the Cylinder descends. What is the acceleration of the Cylinder ?
If a man can push with a maximum force of 90 N, how far from the door's rotation axis must he apply this force if 110-Nm torque is needed to start rotating a revolving door?
A wooden beam of mass 150 kg and length 10m is suspended from a horizontal wall support at the left end and connected by a cable to the same wall at the right end. The cable makes an angle of 45º with the horizontal. A person of mass 42 kg stands on the beam 2.5 m from the left wall. A 25 kg child also rests on the beam, at 7m from the left wall. Calculate the tension in the rope and the force exerted by the wall on the beam.
Practice: Balanced beam
A uniform 90 kg beam is resting on two supports as shown below. The supports are 20 cm and 80 cm away from the two ends of beam. If the beam is 180 cm, what are the forces acting on the beam from supports A and B?
Forces: Standing on a beam
A horizontal beam with a length of 8.0 meters and weight of 200 N is attached to a wall by a pin connection. Its far end is attached to the cable that makes angle of 53 degrees with the beam. A person of weight 600 N stands 2.0 meters away from the wall. What is the tension of the cable (T) and the magnitude of the force that wall applies on the beam (R), respectively?
Hint: The total reaction force is the sum of a normal force (perpendicular to the wall) and a friction force (parallel to the wall). So the net reaction force will be at an angle. (In this problem we are not ignoring friction at the wall). In this problem, there are a few ways to solve it; but you can just treat the reaction force as a single force that provides a single torque at an angle to find the answer.
Torque due to a Magnetic Field
A circular loop of radius 10.5 cm and 40 turns has a current of 2.50 A flowing through the coil. A magnetic field of strength 3.4 T acts at an angle of 35º to the normal of the plane of the loop. What is the magnitude of the net torque acting on the loop?
torque
Newton’s First Law does not apply to rotating objects
Practice: Torque on a Circular Current Loop
Torque on a Circular Current Loop
Forces: Friction
A block is sliding on gym floor. The coefficient of static and kinetic friction between the block and the floor are 0.40.40.4and 0.070.070.07 respectively. If the block is initially traveling at 3 m/s3\ m/s3 m/s find the total distance the block must travel to stop. Draw and label a FBD for both the initial state and the final state.
A 5 kg5\ kg5 kgblock is being pulled along at table by a cable and is accelerating along the surface at 2[ms2]2\left[\frac{m}{s^2}\right]2[s2m]. The coefficient of kinetic friction between the block and the table is 0.100.100.10. Draw the
system then find the tension in the cable. Does the force in the cable change if the system is frictionless? Why or why not?
If the coefficient of static friction between the block and the ramp is 0.40.40.4, find the minimum angle such that the block will slide down the slope.
Force: Friction calculations
Alice is pushing her little brother, Bob, on ice. Alice weights 35 kg35\ kg35 kg while her little brother only weights 15 kg15\ kg15 kg. The coefficient of kinetic friction between Bob's shoes and ice is 0.10.10.1and they have acceleration equal to 2 ms22\ \frac{m}{s^2}2 s2m.
a) Find the force that Alice exert on Bob.
b) Find the coefficient of static friction between Alice's shoes and ice.
A block is sliding on gym floor. The coefficient of static and kinetic friction between the block and the floor are 0.400.400.40and 0.0700.0700.070 respectively.
a) Draw and label a FBD for both the initial state and the final state.
b) If the block is initially traveling at 3.0 m/s3.0\ m/s3.0 m/s, find the total distance the block must travel to stop.
A professional mover drags a 20kg mattress across the floor. The mover exerts a force of 50 N at 30° to the horizontal. The coefficient of kinetic friction is 0.100. What is the acceleration of the mattress?
In the following figure, m2 is located on a frictionless surface. If the coefficient of static friction between m1 and m2 is μ\muμ,
what is the minimum force required so that m1 and m2 remain stationery?
I over-packed a box and it weighs 50kg. I'm pulling it across a rough surface at an angle of 45 degrees above the horizontal with a force of 280N. The coefficient of kinetic friction of the floor is 0.5. I pull for 10 seconds, the box speeds up from rest, I release it and it continues to slide to a halt. What is its maximum speed? How long until it stops? What is the box's total displacement?
Dave is driving his truck, now loaded with his 60kg box full of precious and delicate Ming vases. Unfortunately, he did not secure the box in any way to the bed of the truck, thinking that his truck’s filthy floor was `sticky enough' to stop the box moving. μsmax=0.45\mu_{\rm smax}=0.45μsmax=0.45 between the truck floor and the box. He drives at a constant 20 m/s and sees a red light coming up. What is the minimum distance he needs to give himself to stop so that the box does not move?
a) Dave is trying to push a 60kg box up a greased ramp inclined 30°, pushing with a force of 350N. He pushes the box perfectly horizontally, rather than up the ramp, because he’s not terribly bright. What is the box’s acceleration?
b) If Dave forgot his grease at home, the ramp would have μsmax=0.10\mu_{\rm smax}=0.10μsmax=0.10 and μk=0.05.\mu_k=0.05.μk=0.05. He still insists on pushing the box horizontally, with the same force. What would the box’s acceleration be now?
A bus moving at 40 km/h negotiates a 130m radius banked turn designed for 60 km/h. What coefficient of friction is needed to keep the bus on the road?
Vehicles must be able to traverse a curve of radius 60.0 m safely at speeds up to 80 km/h. If the average vehicle weighs 1000 kg, what minimum coefficient of friction is required to make this possible?
An object with mass of 4 kg is moving on a frictionless surface in X direction. It enters a rough region with μ=0.3\mu=0.3μ=0.3. If the velocity of the object is 5msı^5\frac{m}{s}\hat\imath5sm^ , a) what will be its displacement in the rough region? b) What is its velocity half-way through the region? c) Is the motion speeding up or slowing down?
Practice: Pulley
You set up a pulley system as shown. There is kinetic friction acting on the top block (μk=0.175\mu_k=0.175μk=0.175) which has mass 4.5 kg. The vertical block has mass 10.0 kg.
Tugboats (defining systems)
A tugboat of mass 13300 kg has an engine that exerts a force of 112 kN forward while it pulls a much larger boat behind it. This system experiences 16.1 kN of forces resisting motion (think of this as the "friction" between the boat and the water, although there would be more than friction going on in this case).
a) If the acceleration of the system is 0.700 m/s2m/s^2m/s2, what is the mass of the larger boat?
b) Calculate the force exerted by the tugboat on the larger boat, assuming that 14.7 kN of the resistive forces are experienced by the larger boat.
Practice: Box in back of truck
You are driving a flatbed truck. A large box is on the flatbed, at rest relative to the truck. Driving at a speed of 120 km/h, you suddenly need to hit the brakes, slowing down to 100 km/h in 0.64 seconds, because somebody cut you off.
a) What must the coefficient of static friction be to ensure the box does not slip? Is this a realistic coefficient of friction?
b) What does the mass need to be? (Does it matter?)
Driving in a circle
You are driving around a sharp corner, going clockwise. There is a box in the middle of your back seat. If you are driving fast enough, the box will slide to a side of your car. Which side will it slide to? Why?
(Hint: even if questions do not ask you to draw a sketch or picture, you should draw one anyway! It makes life easier for both you and the exam marker.)
Practice: Friction
A 10-kg box is initially at rest on flat surface. A horizontal force of 28 Newton is applied on it. The static and kinetic coefficient of friction between the box and the floor is 0.32 and 0.18. What is the magnitude of the friction force?
Uniform Circular Motion
A 1000kg car rounds a circular track with radius 10m. If μsmax=0.81,\mu _{s\max }=0.81,μsmax=0.81,what is the maximum speed the car can travel?
Friction and a spring
A spring with a spring constant k=340 N/m is used to launch a 1.5kg block along the horizontal surface whose coefficient of sliding friction is 0.27. If the spring is compressed 18cm, how far does the block slide?