Two blocks are attached by a rope over a pulley and are placed on an incline as shown below. A force F is applied to prevent the top block from moving toward the right. If the static and kinetic coefficients of friction of all surfaces are 0.15 and 0.08 respectively, what is the minimum magnitude of F required to prevent being pulled to the right? (Hint: always start these problems with a free-body diagram!)
A) 1.5 N
B) 1.8 N
C) 0.7 N
D) 2.1 N
Unlock full course notes by signing up
Forces: Friction
A block is sliding on gym floor. The coefficient of static and kinetic friction between the block and the floor are 0.40.40.4and 0.070.070.07 respectively. If the block is initially traveling at 3 m/s3\ m/s3 m/s find the total distance the block must travel to stop. Draw and label a FBD for both the initial state and the final state.
A 5 kg5\ kg5 kgblock is being pulled along at table by a cable and is accelerating along the surface at 2[ms2]2\left[\frac{m}{s^2}\right]2[s2m]. The coefficient of kinetic friction between the block and the table is 0.100.100.10. Draw the
system then find the tension in the cable. Does the force in the cable change if the system is frictionless? Why or why not?
If the coefficient of static friction between the block and the ramp is 0.40.40.4, find the minimum angle such that the block will slide down the slope.
Force: Friction calculations
Alice is pushing her little brother, Bob, on ice. Alice weights 35 kg35\ kg35 kg while her little brother only weights 15 kg15\ kg15 kg. The coefficient of kinetic friction between Bob's shoes and ice is 0.10.10.1and they have acceleration equal to 2 ms22\ \frac{m}{s^2}2 s2m.
a) Find the force that Alice exert on Bob.
b) Find the coefficient of static friction between Alice's shoes and ice.
A block is sliding on gym floor. The coefficient of static and kinetic friction between the block and the floor are 0.400.400.40and 0.0700.0700.070 respectively.
a) Draw and label a FBD for both the initial state and the final state.
b) If the block is initially traveling at 3.0 m/s3.0\ m/s3.0 m/s, find the total distance the block must travel to stop.
A professional mover drags a 20kg mattress across the floor. The mover exerts a force of 50 N at 30° to the horizontal. The coefficient of kinetic friction is 0.100. What is the acceleration of the mattress?
In the following figure, m2 is located on a frictionless surface. If the coefficient of static friction between m1 and m2 is μ\muμ,
what is the minimum force required so that m1 and m2 remain stationery?
I over-packed a box and it weighs 50kg. I'm pulling it across a rough surface at an angle of 45 degrees above the horizontal with a force of 280N. The coefficient of kinetic friction of the floor is 0.5. I pull for 10 seconds, the box speeds up from rest, I release it and it continues to slide to a halt. What is its maximum speed? How long until it stops? What is the box's total displacement?
Dave is driving his truck, now loaded with his 60kg box full of precious and delicate Ming vases. Unfortunately, he did not secure the box in any way to the bed of the truck, thinking that his truck’s filthy floor was `sticky enough' to stop the box moving. μsmax=0.45\mu_{\rm smax}=0.45μsmax=0.45 between the truck floor and the box. He drives at a constant 20 m/s and sees a red light coming up. What is the minimum distance he needs to give himself to stop so that the box does not move?
a) Dave is trying to push a 60kg box up a greased ramp inclined 30°, pushing with a force of 350N. He pushes the box perfectly horizontally, rather than up the ramp, because he’s not terribly bright. What is the box’s acceleration?
b) If Dave forgot his grease at home, the ramp would have μsmax=0.10\mu_{\rm smax}=0.10μsmax=0.10 and μk=0.05.\mu_k=0.05.μk=0.05. He still insists on pushing the box horizontally, with the same force. What would the box’s acceleration be now?
A bus moving at 40 km/h negotiates a 130m radius banked turn designed for 60 km/h. What coefficient of friction is needed to keep the bus on the road?
Vehicles must be able to traverse a curve of radius 60.0 m safely at speeds up to 80 km/h. If the average vehicle weighs 1000 kg, what minimum coefficient of friction is required to make this possible?
An object with mass of 4 kg is moving on a frictionless surface in X direction. It enters a rough region with μ=0.3\mu=0.3μ=0.3. If the velocity of the object is 5msı^5\frac{m}{s}\hat\imath5sm^ , a) what will be its displacement in the rough region? b) What is its velocity half-way through the region? c) Is the motion speeding up or slowing down?
Practice: Pulley
You set up a pulley system as shown. There is kinetic friction acting on the top block (μk=0.175\mu_k=0.175μk=0.175) which has mass 4.5 kg. The vertical block has mass 10.0 kg.
Tugboats (defining systems)
A tugboat of mass 13300 kg has an engine that exerts a force of 112 kN forward while it pulls a much larger boat behind it. This system experiences 16.1 kN of forces resisting motion (think of this as the "friction" between the boat and the water, although there would be more than friction going on in this case).
a) If the acceleration of the system is 0.700 m/s2m/s^2m/s2, what is the mass of the larger boat?
b) Calculate the force exerted by the tugboat on the larger boat, assuming that 14.7 kN of the resistive forces are experienced by the larger boat.
Practice: Box in back of truck
You are driving a flatbed truck. A large box is on the flatbed, at rest relative to the truck. Driving at a speed of 120 km/h, you suddenly need to hit the brakes, slowing down to 100 km/h in 0.64 seconds, because somebody cut you off.
a) What must the coefficient of static friction be to ensure the box does not slip? Is this a realistic coefficient of friction?
b) What does the mass need to be? (Does it matter?)
Driving in a circle
You are driving around a sharp corner, going clockwise. There is a box in the middle of your back seat. If you are driving fast enough, the box will slide to a side of your car. Which side will it slide to? Why?
(Hint: even if questions do not ask you to draw a sketch or picture, you should draw one anyway! It makes life easier for both you and the exam marker.)
Practice: Friction
A 10-kg box is initially at rest on flat surface. A horizontal force of 28 Newton is applied on it. The static and kinetic coefficient of friction between the box and the floor is 0.32 and 0.18. What is the magnitude of the friction force?
Uniform Circular Motion
A 1000kg car rounds a circular track with radius 10m. If μsmax=0.81,\mu _{s\max }=0.81,μsmax=0.81,what is the maximum speed the car can travel?
Practice: Condition of Static Equilibrium
A 3.0 m ladder of mass 12 kg rests against a frictionless wall. The coefficient of friction between the ladder and the floor is 0.60. What is the smallest angle that the ladder can make with the ground if the ladder is to remain at rest? (in degrees) Neglect the friction between the ladder and the wall.
A block with mass m is set to move up an inclined plane.
a) Assume there is no friction, how far will the block slide before come to a stop?
b) Now, assume there is friction between the block and the plane, how far will the block go up the plane?
Minimum sliding angle
If the coefficient of static friction between the block and the ramp is 0.40.40.4, find the minimum angle such that the block will slide down the slope. Give your answer to two sig figs in degrees.
I over-packed a box and it weighs 50kg. I'm pulling it across a rough surface at an angle of 45 degrees above the horizontal with a force of 280N. The coefficient of kinetic friction of the floor is 0.50. I pull for 10 seconds, which causes the box speed up from rest. Then I release it, and it continues to slide, as it slows to a halt.
a) What is its maximum speed?
b) How long until it stops?
Two blocks of mass m and M are connected via pulley with a configuration as shown. The surfaces are frictionless. If M=15 kg and m=8 kg and θ1=30 and θ2=60\theta_1=30\ {\rm and}\ \theta_2=60θ1=30 and θ2=60
Find the acceleration
What is the tension in the string?
A 1.2 kg is at rest on a spring at the base of a 35 degree inclined plane. If the spring constant is 105 N/m, and the spring is compressed by 12 cm, how far will it travel up the incline when it is release?
1) Two masses are attached together by a rope as shown in the picture. If the system is released from the rest, what is the direction of the motion and acceleration for each mass? (Imagine there is no friction between masses and the inclined surface) M2 = 2M1 = 2kg
Forces: Inclined surface
A 40kg wagon attached to a rope is pulled up a hill at an incline of 19° to the horizontal. If the wagon starts from rest and takes 50 seconds to move 92 m up the hill, what is the force of tension in the rope? Find the acceleration of the block.
I'm moving and packed all my books into a box that weighs 17kg. I pull the box on a weightless dolly with a force of 60N at an angle of 30° to the horizontal surface. What is the acceleration of the box?
A car travelling at 25 m/s on an uphill with θ = 20° slope runs out of the gas. a) How far up the hill it can move before starting to roll back down?
b) How long does it take for the car to get to the turning point?
A stationary snow/water skier starts to slid down an icy slope inclined 11° until it hits the water. Initially skier is 200 meter away from the surface on the inclined surface. When he hits the water, the skier comes to full stop in 80 meters on the surface of water.
a) What is the acceleration of the skier on the icy slope?
b) How long does it take for the skier to hit the water?
Inclined pully system
Two blocks are connected by a pulley system. One block (10 kg) rests on a plane inclined at 35º to the horizontal, while the other block (9.0 kg) hangs off the edge of the incline. The coefficient of friction between the block and the table is 0.30. The blocks are released from rest, what are their accelerations and what is the tension?
A fixed triangular wedge has two inclined surfaces forming a double inclines plane. Two masses m1 = 5 kg and m2 = 10 kg are attached to a massless pulley connected with an inextensible string. The inclined surface I1 and I2 make an angle α1=60∘\alpha_1=60^\circα1=60∘ and α2=30∘\alpha_2=30^\circα2=30∘ with the horizontal respectively. The coefficient of kinetic friction is μ=0.01.\mu=0.01.μ=0.01. Assume g = 10 m/s2.
a) Draw a free body diagram.
b) Is the system stationary? If not what will be the net acceleration?
A 1400-kg truck ascends a steep road at a speedy 60 km/h, against a 450-N force of air resistance. If the engine supplies energy to the drive wheels at the rate of 38 kW, what is the slope of the road?
Two different boxes of masses m1 = 125kg and m2 = 45kg are sliding down a rough inclined plane angled at θ=35∘\theta = 35^\circθ=35∘ , as seen in the figure. The coefficient of kinetic friction between m1 and the plane is 0.3. The coefficient between m2 and the plane is 0.5. Find the acceleration of the two boxes and the contact force between them.
Practice: Inclined Plane
A box of 10 Kg10\ Kg10 Kg is released from rest at t=0 st=0\ st=0 sfrom the top of a frictionless inclined surface with θ=45°\theta=45\degreeθ=45°. If the box is initially at the top of inclined surface with height of 2 m2\ m2 mrespect to the bottom of the ramp, at what time the box gets to the ground?
Practice: Inclined Plane Theory
Inclined Plane
Sliding down an inclined plane is another example of motion with constant acceleration.
Source of the motion is still gravity of earth but only part of it is affecting the sliding of the object
Forces: Block on slope with friction
A mass of 5 kg5\ kg5 kg is stationary on the surface of an inclined surface with angle of θ\thetaθand coefficient of kinetic friction of 0.30.30.3 and coefficient of static friction of 0.50.50.5. You start increasing the angle of the inclines surface.
Two masses on a pulley on a slope
Two blocks of mass m and M are connected via pulley with a configuration as shown. The surfaces are frictionless. If M=15 kg and m=8 kg and θ1=30 and θ2=60\theta_1=30\ {\rm and}\ \theta_2=60θ1=30 and θ2=60,
Find the acceleration of the system.