High School
SAT
ACT
University
MCAT
LSAT
DAT

Friction and a spring

Related Topics

Wize University Physics Textbook (Master) > Newton's Laws of Motion: Forces and Dynamics

Spring Force

4 Activities

Wize University Physics Textbook (Master) > Newton's Laws of Motion: Forces and Dynamics

Friction

4 Activities

Practice: Friction and a Spring

A spring with a spring constant k=340 N/m is used to launch a 1.5kg block along the horizontal surface whose coefficient of sliding friction is 0.27. If the spring is compressed 18cm, how far does the block slide?


More Spring Force Questions:
A 1.2 kg is at rest on a spring at the base of a 35 degree inclined plane. If the spring constant is 105 N/m, and the spring is compressed by 12 cm, how far will it travel up the incline when it is release?
Vertical spring
The springs AA, BBand CChave the same initial length. If kA=kC=0.5kBk_A=k_C=0.5k_B,
a) Find the values of mBm_B, mCm_C.
b) Rank the period of oscillations.
Problems on Momentum Conservation and Collisions
Practice: Conservation of Momentum with Spring
A 15.0-kg block is attached to a very light horizontal spring with spring constant 500 N/m and is resting on a friction-less horizontal table. It is struck by a 3.00-kg stone traveling horizontally at 8.00 m/s to the right. The stone rebounds at 2.00 m/s horizontally to the left. Find the maximum distance that the block will compress the spring after the collision. Enter the answer with 3 significant digits.
Hooke's Law and Simple Harmonic Motion
A stretchy rope suspended from the ceiling is 59 cm long when a 70 N weight hangs from it, but is 80 cm long when a 205 N weight hangs from it. Determine the spring constant “k” of the rope.
Momentum and spring
A 15.0-kg block is attached to a very light horizontal spring with spring constant 500 N/m and is resting on a friction-less horizontal table. It is struck by a 3.00-kg stone traveling horizontally at 8.00 m/s to the right. The stone rebounds at 2.00 m/s horizontally to the left. Find the maximum distance that the block will compress the spring after the collision.
Practice: Spring constant
A 300-gram ball starts to roll down 4 meters on a 30 degree incline. (That is, the distance it travels along the slope is 4 meters.) The ball then rolls 2 meters on flat surface and hits a plate, connected to a spring. The spring is compressed 25 cm. If the kinetic coefficient of friction of all surfaces is 0.1, what is the spring constant?
Practice: Friction and a spring
A spring with a spring constant k=340 N/m is used to launch a 1.5kg block along the horizontal surface whose coefficient of sliding friction is 0.27. If the spring is compressed 18cm, how far does the block slide?
Energy conservation and circular motion
A compressed spring is used to propel a 25-gram ball-bearing along a frictionless horizontal track which contains a circular vertical loop of radius 0.30 m in a vertical plane. The spring obeys Hooke's law and is compressed 20 cm by a force of 5.0 N.
a) What is the speed of the ball-bearing at the top of the loop? Treat the ball bearing as a point mass.
b) What is the minimum spring compression required to have the ball-bearing complete a full loop?
Practice: Springs and slopes
A 2.00-kg block is pushed against a spring with negligible mass and force constant k= 400 N/m, compressing it 0.220 m. When the block is released , it moves along a friction-less , horizontal surface and then up a friction-less incline with slope 37.0∘37.0^{\circ}(Fig).
A 2 kg block rests on a spring as shown above, when a 3 kg block is dropped from a height of 3 m above it. The spring constant is 28 N/m. Determine:
The system below initially starts from rest, with a spring constant of 28 N/m.
At t = 0, the 3 kg block is removed. If the 2 kg block is not attached to the spring:
Friction and a spring
A spring with a spring constant k=340 N/m is used to launch a 1.5kg block along the horizontal surface whose coefficient of sliding friction is 0.27. If the spring is compressed 18cm, how far does the block slide?
Problems on Momentum Conservation and Collisions
A 15.0-kg block is attached to a very light horizontal spring with spring constant 500 N/m and is resting on a friction-less horizontal table. It is struck by a 3.00-kg stone traveling horizontally at 8.00 m/s to the right. The stone rebounds at 2.00 m/s horizontally to the left. Find the maximum distance that the block will compress the spring after the collision. Enter the answer with 3 significant digits.
A 1.2 kg is at rest on a spring at the base of a 35 degree inclined plane. If the spring constant is 105 N/m, and the spring is compressed by 12 cm, how far will it travel up the incline when it is release?
Hooke's Law and Simple Harmonic Motion
A stretchy rope suspended from the ceiling is 59 cm long when a 70 N weight hangs from it, but is 80 cm long when a 205 N weight hangs from it. Determine the spring constant “k” of the rope.
Vertical spring
The springs AA, BBand CChave the same initial length. If kA=kC=0.5kBk_A=k_C=0.5k_B,
a) Find the values of mBm_B, mCm_C.
b) Rank the period of oscillations.
This question concerns the great garbage patch in the middle of Pacific ocean. Consider the garbage patch to be a perfect cylinder. At this moment 100 seagulls are sitting on the patch. Every time a wave hits the garbage patch the garbage patch bobs up and down 5 times in 7.2 seconds. When the garbage patch is still the 100 seagulls leave. You know notice that the garbage bobs up and down 5 times in 7 seconds.
The garbage patch weighs 1000 kg. (To make calculations simpler this number is much smaller than the real number.)
a) What is the total mass of the 100 seagulls
A 0.15 kg frame, when suspended from a coil spring, stretches the spring 0.070 m.A 0.200-kg lump of putty is dropped from rest onto the frame from a height of 30.0 cm(Fig). Find the maximum distance the frame moves downward from its initial position.
More Friction Questions:
Kinematics: Friction
Alice decides to push her little brother Bob on ice. Bob weights 3030 kg. Initially, the force Alice is applying on Bob is not enough to start the motion. Alice gradually increases the force on Bob until he starts to slide. After that, Alice keeps pushing Bob (with the same force that she was applying when Bob started to move) for the next 33 s and then lets him go. Bob is going to stop a little bit later. The coefficient of kinetic friction between Bob's shoes and ice is 0.10.1 and the coefficient of static friction between his shoes and ice is 0.20.2.
a) Find Bob's speed at the moment when Alice lets him go.
b) How long does it take for Bob to stop completely after Alice lets him go?
Kinematics: Friction
Alice decides to push her little brother Bob on ice. Bob weights 3030 kg. Initially, the force Alice is applying on Bob is not enough to start the motion. Alice gradually increases the force on Bob until he starts to slide. After that, Alice keeps pushing Bob (with the same force that she was applying when Bob started to move) for the next 33 s and then lets him go. Bob is going to stop a little bit later. The coefficient of kinetic friction between Bob's shoes and ice is 0.10.1 and the coefficient of static friction between his shoes and ice is 0.20.2.
a) Find Bob's speed at the moment when Alice lets him go.
b) How long does it take for Bob to stop completely after Alice lets him go?
trapezoid and friction
Two blocks are attached by a rope over a pulley and are placed on an incline as shown below. A force F is applied to prevent the top block from moving toward the right. If the static and kinetic coefficients of friction of all surfaces are 0.15 and 0.08 respectively, what is the minimum magnitude of F required to prevent being pulled to the right? (Hint: always start these problems with a free-body diagram!)
If the coefficient of static friction between the block and the ramp is 0.40.4, find the minimum angle such that the block will slide down the slope.
Kinematics: Friction
Alice decides to push her little brother Bob on ice. Bob weights 3030 kg. Initially, the force Alice is applying on Bob is not enough to start the motion. Alice gradually increases the force on Bob until he starts to slide. After that, Alice keeps pushing Bob (with the same force that she was applying when Bob started to move) for the next 33 s and then lets him go. Bob is going to stop a little bit later. The coefficient of kinetic friction between Bob's shoes and ice is 0.10.1 and the coefficient of static friction between his shoes and ice is 0.20.2.
a) Find Bob's speed at the moment when Alice lets him go.
b) How long does it take for Bob to stop completely after Alice lets him go?
Practice: Pulley
You set up a pulley system as shown. There is kinetic friction acting on the top block (μk=0.175\mu_k=0.175) which has mass 4.5 kg. The vertical block has mass 10.0 kg.
A block is sliding on gym floor. The coefficient of static and kinetic friction between the block and the floor are 0.400.40and 0.0700.070 respectively.
a) Draw and label a FBD for both the initial state and the final state.
b) If the block is initially traveling at 3.0 m/s3.0\ m/s, find the total distance the block must travel to stop.
Forces: Friction
Consider a hardcover textbook that you are pressing against a wall. Your pushing force against the book is horizontal, and perpendicular to the wall. The book has a mass of 2.0 kg and the coefficients of kinetic and static friction between the book and the wall are 0.30 and 0.40, respectively.
a) How much force do you have to apply to just barely keep the book from falling?
b) How much force would you have to apply if you were instead pushing upwards and into the wall, at an angle of 20 degrees above horizontal?
Driving in a circle
You are driving around a sharp corner, going clockwise. There is a box in the middle of your back seat. If you are driving fast enough, the box will slide to a side of your car. Which side will it slide to? Why?
(Hint: even if questions do not ask you to draw a sketch or picture, you should draw one anyway! It makes life easier for both you and the exam marker.)
Practice: Box in back of truck
You are driving a flatbed truck. A large box is on the flatbed, at rest relative to the truck. Driving at a speed of 120 km/h, you suddenly need to hit the brakes, slowing down to 100 km/h in 0.64 seconds, because somebody cut you off.
a) What must the coefficient of static friction be to ensure the box does not slip? Is this a realistic coefficient of friction?
b) What does the mass need to be? (Does it matter?)
Newton's third
Let m = 2.50kg and M = 3.00kg. The following situation is given:
The coefficient of kinetic friction between masses is μk,Mm =0.840\mu_{k,Mm}\ =0.840 and between M and the ground is μk,MG = 0.230\mu_{k,MG}\ =\ 0.230.
The coefficient of static friction between masses is μs,Mm=0.950\mu_{s,Mm}=0.950 and between M and the ground is μs,MG =0.320\mu_{s,MG}\ =0.320.
Alice and Bob, arguing and fighting over the usage of the imperial system, are facing each other and pushing. Alice is facing +x, and Bob is facing -x. They are both on a slippery surface and are sliding along together at a steady 4m/s. Which of the following statements are true?
Two cats are on a slanted roof, and they are both not moving. Cat 1 is 2.0kg, and Cat 2 is 3.0kg. Which cat is experiencing the highest frictional force?
I over-packed a box and it weighs 50kg. I'm pulling it across a rough surface at an angle of 45 degrees above the horizontal with a force of 280N. The coefficient of kinetic friction of the floor is 0.5. I pull for 10 seconds, the box speeds up from rest, I release it and it continues to slide to a halt. What is its maximum speed?
Friction and a spring
A spring with a spring constant k=340 N/m is used to launch a 1.5kg block along the horizontal surface whose coefficient of sliding friction is 0.27. If the spring is compressed 18cm, how far does the block slide?
Tugboats (defining systems)
A tugboat of mass 13300 kg has an engine that exerts a force of 112 kN forward while it pulls a much larger boat behind it. This system experiences 16.1 kN of forces resisting motion (think of this as the "friction" between the boat and the water, although there would be more than friction going on in this case).
a) If the acceleration of the system is 0.700 m/s2m/s^2, what is the mass of the larger boat?
b) Calculate the force exerted by the tugboat on the larger boat, assuming that 14.7 kN of the resistive forces are experienced by the larger boat.
The magnitude of the force of static friction is linearly proportional to the applied external force.
work done by force of friction
A 5 kg block is moved up a 30 degree incline by a force of 50 N, parallel to the incline. The coefficient of kinetic friction between the block and the incline is .25. How much work is done by the 50 N force in moving the block a distance of 10 meters? What is the total work done on the block over the same distance?
The mass of the bar is 4 kg. The coefficient of static friction between the bar and the floor is 0.3. Neglect friction between the bar and the wall.
(a) If α=20°\alpha = 20\degree what is the magnitude of the friction force exerted on the bar by the floor?
(b) What is the maximum angle α\alphafor which the bar will not slip
Work done by friction
When a body slides against a rough horizontal surface, the work done by friction is ___________
An object with mass of 4 kg is moving on a frictionless surface in X direction. It enters a rough region with μ=0.3\mu=0.3. If the velocity of the object is 5msı^5\frac{m}{s}\hat\imath , a) what will be its displacement in the rough region? b) What is its velocity half-way through the region? c) Is the motion speeding up or slowing down?
In the following figure, m2 is located on a frictionless surface. If the coefficient of static friction between m1 and m2 is μ\mu,
what is the minimum force required so that m1 and m2 remain stationery?
trapezoid and friction
Two blocks are attached by a rope over a pulley and are placed on an incline as shown below. A force F is applied to prevent the top block from moving toward the right. If the static and kinetic coefficients of friction of all surfaces are 0.15 and 0.08 respectively, what is the minimum magnitude of F required to prevent being pulled to the right? (Hint: always start these problems with a free-body diagram!)
The Work-Energy Theorem: Friction
A car parked on a 32- degree steep hill loses its traction and starts to come down. It travels 160 meters on the hill until it reaches speed of 72 km/h. What is the kinetic coefficient of friction between the car and the surface?
Practice: Friction
A 10-kg box is initially at rest on flat surface. A horizontal force of 28 Newton is applied on it. The static and kinetic coefficient of friction between the box and the floor is 0.32 and 0.18. What is the magnitude of the friction force?
Practice: Alice Pushes Her Brother Bob
Alice decides to push her little brother Bob on ice. Bob weights 30kg. Initially, the force Alice is applying on Bob is not enough to start the motion. Alice increases the force on Bob gradually until he starts to slide. After that, Alice keeps pushing Bob with the same force that she were applying when Bob started moving for the next 3s and then lets him go. Bob is going to stop a little bit later. The coefficient of kinetic friction between Bob's shoes and ice is 0.10.1and the coefficient of static friction between his shoes and ice is 0.2.
a) Find speed of Bob when Alice letting him go.
A bus moving at 40 km/h negotiates a 130m radius banked turn designed for 60 km/h. What coefficient of friction is needed to keep the bus on the road?
Uniform Circular Motion
A 1000kg car rounds a circular track with radius 10m. If μsmax⁡=0.81,\mu _{s\max }=0.81,what is the maximum speed the car can travel?
Practice: Condition of Static Equilibrium
A 3.0 m ladder of mass 12 kg rests against a frictionless wall. The coefficient of friction between the ladder and the floor is 0.60. What is the smallest angle that the ladder can make with the ground if the ladder is to remain at rest? (in degrees) Neglect the friction between the ladder and the wall.
a) Dave is trying to push a 60kg box up a greased ramp inclined 30°, pushing with a force of 350N. He pushes the box perfectly horizontally, rather than up the ramp, because he’s not terribly bright. What is the box’s acceleration?
b) If Dave forgot his grease at home, the ramp would have μsmax=0.10\mu_{\rm smax}=0.10 and μk=0.05.\mu_k=0.05. He still insists on pushing the box horizontally, with the same force. What would the box’s acceleration be now?
Dave is driving his truck, now loaded with his 60kg box full of precious and delicate Ming vases. Unfortunately, he did not secure the box in any way to the bed of the truck, thinking that his truck’s filthy floor was `sticky enough' to stop the box moving. μsmax=0.45\mu_{\rm smax}=0.45 between the truck floor and the box. He drives at a constant 20 m/s and sees a red light coming up. What is the minimum distance he needs to give himself to stop so that the box does not move?
I over-packed a box and it weighs 50kg. I'm pulling it across a rough surface at an angle of 45 degrees above the horizontal with a force of 280N. The coefficient of kinetic friction of the floor is 0.5. I pull for 10 seconds, the box speeds up from rest, I release it and it continues to slide to a halt. What is its maximum speed? How long until it stops? What is the box's total displacement?
Force: Friction calculations
Alice is pushing her little brother, Bob, on ice. Alice weights 35 kg35\ kg while her little brother only weights 15 kg15\ kg. The coefficient of kinetic friction between Bob's shoes and ice is 0.10.1and they have acceleration equal to 2 ms22\ \frac{m}{s^2}.
a) Find the force that Alice exert on Bob.
b) Find the coefficient of static friction between Alice's shoes and ice.
If the coefficient of static friction between the block and the ramp is 0.40.4, find the minimum angle such that the block will slide down the slope.
A 5 kg5\ kgblock is being pulled along at table by a cable and is accelerating along the surface at 2[ms2]2\left[\frac{m}{s^2}\right]. The coefficient of kinetic friction between the block and the table is 0.100.10. Draw the
system then find the tension in the cable. Does the force in the cable change if the system is frictionless? Why or why not?
Forces: Friction
A block is sliding on gym floor. The coefficient of static and kinetic friction between the block and the floor are 0.40.4and 0.070.07 respectively. If the block is initially traveling at 3 m/s3\ m/s find the total distance the block must travel to stop. Draw and label a FBD for both the initial state and the final state.
Forces: Friction
A professional mover drags a 20kg mattress across the floor. The mover exerts a force of 50 N at 30° to the horizontal. The coefficient of kinetic friction is 0.100. What is the acceleration of the mattress?
Vehicles must be able to traverse a curve of radius 60.0 m safely at speeds up to 80 km/h. If the average vehicle weighs 1000 kg, what minimum coefficient of friction is required to make this possible?
Force of friction
A 400-gram package lying on a horizontal surface is attached to a horizontal string that passes over a smooth pulley. When a mass of 200 grams is attached to the other end of the string, the package is on the point of moving. Find the coefficient of friction.